I - Wifi
Kommando |
Wert |
Beschreibung |
---|---|---|
AP |
Show current selected Wifi Access Point (AP) Zeigt den aktuell ausgewählten Wifi-Zugangspunkt. |
|
AP |
0 |
Switch to other Wifi Access Point (AP) Wechselt zum anderen Wifi-Zugangspunkt. |
AP |
1 |
Select Wifi Access Point 1 (AP) Wählt Wifi-Zugangspunkt Nr.1 |
AP |
2 |
Select Wifi Access Point 2 (AP) Wählt Wifi-Zugangspunkt Nr.2 |
Hostname |
Show current hostname Zeigt den aktuellen Hostnamen. |
|
Hostname |
1 |
Reset hostname to Setzt den Hostnamen zu |
Hostname |
<host> |
Set hostname (32 chars max) and restart. If <host> contains % the hostname will be reset to the default. Ändert den Hostnamen (max 32 Zeichen) und fürht Neustart durch. Wenn <host> ein %-Zeichen enthält, wird der Hostnamen auf Standard zurückgesetzt. |
IPAddress1 |
Show current IP address Zeigt die aktuelle IP-Adresse an. |
|
IPAddress1 |
0.0.0.0 |
Use dynamic IP addresses (DHCP) [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] Benutzt dynamische IP-Adressen (DHCP). [Anschließend "restart 1" eingeben, wenn die Einstellungen von IP-Adresse, Subnetz-Maske und Gateway fertig sind] |
IPAddress1 |
x.x.x.x |
Set (decimal) static IP address [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] Setzt statische IP-Adresse für dieses Gerät. [Anschließend "restart 1" eingeben, wenn die Einstellungen von IP-Adresse, Subnetz-Maske und Gateway fertig sind] |
IPAddress2 |
Show current IP address of Gateway Zeigt die aktuelle IP-Adresse vom Gateway. |
|
IPAddress2 |
x.x.x.x |
Set (decimal) IP address of Gateway [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] Setzt die IP-Adresse des Gateways. [Anschließend "restart 1" eingeben, wenn die Einstellungen von IP-Adresse, Subnetz-Maske und Gateway fertig sind] |
IPAddress3 |
Show current subnet mask Zeigt die aktuelle Subnetz-Maske an. |
|
IPAddress3 |
x.x.x.x |
Set (decimal) subnet mask [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] Setzt die Subnetz-Maske. [Anschließend "restart 1" eingeben, wenn die Einstellungen von IP-Adresse, Subnetz-Maske und Gateway fertig sind] |
IPAddress4 |
Show current IP address of DNS server Zeigt die aktuelle IP-Adresse des DNS-Servers an. |
|
IPAddress4 |
x.x.x.x |
Set (decimal) IP address of DNS server [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] Setzt die IP-Adresse des DNS-Servers. [Anschließend "restart 1" eingeben, wenn die Einstellungen von IP-Adresse, Subnetz-Maske und Gateway fertig sind] |
NtpServer<x> |
Show NTP server 1 to 3 name or ip address Zeigt die IP-Adressen oder den Namen der NTP-Server 1 bis 3 an. |
|
NtpServer<x> |
0 |
Set NTP server 1 to 3 name to none and restart Setzt die Einstellungen für NTP-Server 1 bis 3 zurück und führt einen Neustart durch. |
NtpServer<x> |
1 |
Reset NTP server 1 to 3 name to Setzt NTP-Server 1 bis 3 auf den Wert in der |
NtpServer<x> |
<ntphost> |
Set NTP server 1 to 3 name or ip address (32 chars max) Setzt die IP-Adresse oder den Namen von NTP-Server 1 bis 3. |
Password |
Show AP1 current Wifi password Zeigt das Passwort vom ersten Wifi-Zuganspunkt an. (AP1) |
|
Password |
1 |
Reset AP1 Wifi password to Setzt das Passwort vom ersten Wifi-Zugangspunkt (AP1) auf den Wert in der |
Password |
<pwd> |
Set AP1 Wifi password (64 chars max) and restart Setzt das Passwort für den ersten Wifi-Zugangspunkt (AP1) (maximal 64 Zeichen) und führt einen Neustart durch. |
Password<x> |
Show APx current Wifi password Zeigt das Passwort vom jeweiligen Wifi-Zuganspunkt an. (APx) |
|
Password<x> |
1 |
Reset APx Wifi password to Setzt das Passwort vom jeweiligen Wifi-Zugangspunkt (APx) auf den Wert in der |
Password<x> |
<pwd> |
Set APx Wifi password (64 chars max) and restart Setzt das Passwort für den jeweiligen Wifi-Zugangspunkt (APx) (malximal 64 Zeichen) und führt einen Neustart durch. |
SSId / SSId<x> |
Show APx current Wifi SSId Zeigt die aktuelle Netzwerkkennung (SSID) des jeweiligen Wifi-Zugangspunktes (APx). |
|
SSId / SSId<x> |
1 |
Reset APx Wifi SSId to Setzt die Netzwerkkennung (SSID) auf den Wert in der |
SSId / SSId<x> |
<ssid> |
Set APx Wifi SSId (32 chars max) and restart Setzt die Netzwerkkennung (SSID) (maximal 32 Zeichen) |
SetOption56 |
(6.3.0.10) Enable wifi network scan to select strongest signal on restart (ab Firmware 6.3.0.10) Aktiviert den Netzwerk-Scan beim Neustart, um das stärkste Wifi-Signal auszuwählen. |
|
SetOption57 |
(6.3.0.10) Enable wifi network scan every 44 minutes to switch to +10dB stronger signal if detected (ab Firmware 6.3.0.10)Aktiviert den Netzwerk-Scan alle 44 Minuten, um ein stärkeres Wifi-Signal (+10dB) auszuwählen, falls verfügbar. |
|
WebPassword |
Show current web server Admin password for user |
|
WebPassword |
0 |
Disable use of password Deaktivert die Passworteingabe |
WebPassword |
1 |
Reset password to value in Setzt das Passwort auf den Wert in der |
WebPassword |
<pwd> |
Set web server Admin password for user Setzt das Administrator-Passwort des Webservers für |
WebSend |
[<host>] <command> |
Send command to host where host is hostname or IP address. If command start with a \ it will be used as a link Sendet Kommando an anderen Host. <host> ist Hostname oder IP-Adresse. Wenn das Kommando mit \ anfängt, wird es als Link verwendet. |
WebSend |
[<host>:<port>] <command> |
Send command to host where host is hostname or IP address Sendet Kommando an anderen Host (mit Portangebe). <host> ist Hostname oder IP-Adresse. Wenn das Kommando mit \ anfängt, wird es als Link verwendet. |
WebSend |
[<host>,<user>:<password>] <command> |
Send command to host where host is hostname or IP address Sendet Kommando an anderen Host (mit Benutzernamen und Passwort). <host> ist Hostname oder IP-Adresse. Wenn das Kommando mit \ anfängt, wird es als Link verwendet. |
WebSend |
[<host>:<port>,<user>:<password>] <command> |
Send command to host where host is hostname or IP address Sendet Kommando an anderen Host (mit Port, Benutzernamen und Passwort). <host> ist Hostname oder IP-Adresse. Wenn das Kommando mit \ anfängt, wird es als Link verwendet. |
WebServer |
Show current web server state Zeigt den aktuellen Status des Webservers an. |
|
WebServer |
0 / off |
Stop web server Stoppt den Webserver. |
WebServer |
1 / user |
Start web server in user mode Startet den Webserver im Benutzer-Modus. |
WebServer |
2 / admin |
Start web server in admin mode Startet den Webserver im Administrator-Modus. |
WifiConfig |
Show current config tool Zeigt aktuelle Einstellung der Wifi-Konfiguration. |
|
WifiConfig |
0 |
Disable wifi config but restart (used with alternate AP) Deaktiviert die Wifi-Konfiguration und führt einen Neustart durch. (Mit alternativem Wifi-Zugangspunkt) |
WifiConfig |
1 |
Start smart config for 1 minute and set as current config tool Startet die Smart-Config für eine Minute und setzt dies als Standard Wifi-Konfiguration. |
WifiConfig |
2 |
Start wifi manager (web server at 192.168.4.1) and set as current config tool Startet den Wifi-Manager (Webserver auf 192.168.4.1) und setzt dies als Standard Wifi-Konfiguration. |
WifiConfig |
3 |
Start WPS config for 1 minute and set as current config tool Startet WPS und setzt dies als Standard Wifi-Konfiguration. |
WifiConfig |
4 |
Disable wifi config but retry other AP without restart Deaktiviert die Wifi-Konfiguration probiert den anderen Wifi-Zugangspunkt ohne Neustart. |
WifiConfig |
5 |
Disable wifi config but retry same AP without restart and flash writes Deaktiviert die Wifi-Konfiguration probiert den gleichen Wifi-Zugangspunkt ohne Neustart. |
Kommentare