I - Wifi
Kommando |
Wert |
Beschreibung |
---|---|---|
AP |
Show current selected Wifi Access Point (AP) Zeigt den aktuell ausgewählten Wifi-Zugangspunkt. |
|
AP |
0 |
Switch to other Wifi Access Point (AP) Wechselt zum anderen Wifi-Zugangspunkt. |
AP |
1 |
Select Wifi Access Point 1 (AP) Wählt Wifi-Zugangspunkt Nr.1 |
AP |
2 |
Select Wifi Access Point 2 (AP) Wählt Wifi-Zugangspunkt Nr.2 |
Hostname |
Show current hostname Zeigt den aktuellen Hostnamen. |
|
Hostname |
1 |
Reset hostname to Setzt den Hostnamen zu |
Hostname |
<host> |
Set hostname (32 chars max) and restart. If <host> contains % the hostname will be reset to the default. Ändert den Hostnamen (max 32 Zeichen) und führt Neustart durch. Wenn <host> ein %-Zeichen enthält, wird der Hostnamen auf Standard zurückgesetzt. |
IPAddress1 |
Show current IP address Zeigt die aktuelle IP-Adresse |
|
IPAddress1 |
0.0.0.0 |
Use dynamic IP addresses (DHCP) [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] Benutzt dynamische IP-Adressen (DHCP). [Gib anschließend "restart 1" ein, wenn die Einstellungen von IP-Adresse, Subnetzmaske und Gateway fertig sind] |
IPAddress1 |
x.x.x.x |
Set (decimal) static IP address [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] |
IPAddress2 |
Show current IP address of Gateway |
|
IPAddress2 |
x.x.x.x |
Set (decimal) IP address of Gateway [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] |
IPAddress3 |
Show current subnet mask |
|
IPAddress3 |
x.x.x.x |
Set (decimal) subnet mask [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] |
IPAddress4 |
Show current IP address of DNS server |
|
IPAddress4 |
x.x.x.x |
Set (decimal) IP address of DNS server [follow this with a "restart 1" command once you complete your IP config of IP Address, subnet mask & gateway] |
NtpServer<x> |
Show NTP server 1 to 3 name or ip address |
|
NtpServer<x> |
0 |
Set NTP server 1 to 3 name to none and restart |
NtpServer<x> |
1 |
Reset NTP server 1 to 3 name to |
NtpServer<x> |
<ntphost> |
Set NTP server 1 to 3 name or ip address (32 chars max) |
Password |
Show AP1 current Wifi password |
|
Password |
1 |
Reset AP1 Wifi password to |
Password |
<pwd> |
Set AP1 Wifi password (64 chars max) and restart |
Password<x> |
Show APx current Wifi password |
|
Password<x> |
1 |
Reset APx Wifi password to |
Password<x> |
<pwd> |
Set APx Wifi password (64 chars max) and restart |
SSId / SSId<x> |
Show APx current Wifi SSId |
|
SSId / SSId<x> |
1 |
Reset APx Wifi SSId to |
SSId / SSId<x> |
<ssid> |
Set APx Wifi SSId (32 chars max) and restart |
SetOption56 |
(6.3.0.10) Enable wifi network scan to select strongest signal on restart |
|
SetOption57 |
(6.3.0.10) Enable wifi network scan every 44 minutes to switch to +10dB stronger signal if detected |
|
WebPassword |
Show current web server Admin password for user |
|
WebPassword |
0 |
Disable use of password |
WebPassword |
1 |
Reset password to value in |
WebPassword |
<pwd> |
Set web server Admin password for user |
WebSend |
[<host>] <command> |
Send command to host where host is hostname or IP address. If command start with a \ it will be used as a link |
WebSend |
[<host>:<port>] <command> |
Send command to host where host is hostname or IP address |
WebSend |
[<host>,<user>:<password>] <command> |
Send command to host where host is hostname or IP address |
WebSend |
[<host>:<port>,<user>:<password>] <command> |
Send command to host where host is hostname or IP address |
WebServer |
Show current web server state |
|
WebServer |
0 / off |
Stop web server |
WebServer |
1 / user |
Start web server in user mode |
WebServer |
2 / admin |
Start web server in admin mode |
WifiConfig |
Show current config tool |
|
WifiConfig |
0 |
Disable wifi config but restart (used with alternate AP) |
WifiConfig |
1 |
Start smart config for 1 minute and set as current config tool |
WifiConfig |
2 |
Start wifi manager (web server at 192.168.4.1) and set as current config tool |
WifiConfig |
3 |
Start WPS config for 1 minute and set as current config tool |
WifiConfig |
4 |
Disable wifi config but retry other AP without restart |
WifiConfig |
5 |
Disable wifi config but retry same AP without restart and flash writes |
Kommentare