Beiträge von marzi

    Neues Firmware Update Verfügbar. 1.4.9.

    Changelog Shelly Firmware 1.4.9

    RGBW2

    Der RGBW2 wurde weiter optimiert und ist nun wesentlich stabiler. Er friert nicht mehr während des normalen Betriebs ein

    Unterstützt % Angaben zur Steuerung. Über die App ist der minimale Schritt 5%

    MQTT

    Langen Tastendruck melden: Der Schalter muss auf „Momentary“ oder „Detached Switch“ stehen und länger als 1 Sek. gedrückt werden

    MQTT-Topic:

    mosquitto_sub -t „shellies/DEVID/longpush/N“

    DEVID – device id

    N – channel number

    Shelly 2 Energieverbrauch über MQTT wurde zurückentwickelt auf 1.4.6 – Ist jetzt behoben!

    MQTT & REST setzen den aktuellen Status-Befehl zurück (Toggle)

    Wurde der Toggle-Befehl ausgeführt, setzt dieser den Status zurück. Sprich, wenn es AN ist, wird es AUS geschaltet und umgekehrt

    MQTT

    -t „shellies/shellyswitch25-05706B/relay/0/command“ -m „toggle“

    REST

    /relay/0?turn=toggle

    Shelly H&T Cloud + MQTT Unterstützung

    WiFi-Symbol für die Stärke des Signals im UI hinzugefügt

    CoAP-Unterstützung

    Shelly 2 berichtet die Position

    Shelly H&T berichtet die Luftfeuchtigkeit

    Kleinere Bugs

    Manuelle Standorteinstellungen werden beim Neustart des Gerätes jetzt korrekt gespeichert



    Change log:

    RGWB2 optimisation and new features (picker freeze fixed)

    RGWB2 are much stable now and do not freeze or reboot during normal usage. RGWB2 support % control from Schedule (over APP Minimum step is 5%)





    Long push button
    reported : switch must be momentary or detached and pushed more than 1 second:

    MQTT topic:

    mosquitto_sub -t "shellies/DEVID/longpush/N"

    DEVID - device id

    N - channel number





    Shelly2, Energy report over MQTT

    It’s Regression at 1.4.6 which is resolved now.

    MQTT and REST revert current status command (toggle)

    Toggle command is added, this command revert the status. If is ON switched OFF and vice version.

    MQTT:

    -t "shellies/shellyswitch25-05706B/relay/0/command" -m "toggle"

    REST:

    /relay/0?turn=toggle


    Shelly HT Cloud + MQTT supported

    You can activate both options for Shelly HT







    Add Wi-Fi strengt as icon in dice UI






    Shelly2: Report roller position over CoAP


    Shelly HT report Humidity over CoAP





    Resolved issue: Manual location settings is not saved when device reboot

    Es gibt was neues vom Shelly 1

    https://shelly.cloud/product/w…-shelly-1pm-switch-relay/



    Description

    • Intelligent On/Off
    • Power Supply: 110-230V ±10%, 50/60Hz AC
    • Compatible with all major international voltage standards.
    • Maximum load current per output: 16A 110-265V, 50/60Hz AC
    • Maximum load current per output: 16A 24 – 60V DC
    • Complies with the following EU standards:
    • Operational temperature: -40 to + 40 °C
    • Dimensions (LxWxH): 41 x 36 x 17 mm
    • Minimum mounting opening: Ø ≥ 50mm
    • Radio signal power: 1mW
    • Wireless/WiFi Protocol: 802.11 b/g/n
    • Radio frequency: 2400 – 2500 MHz
    • Range: up to 50 m outdoors and up to 30 m indoors (depending on the building materials)
    • Power metering
    • Overload and temperature protection
    • Electrical power consumption < 1 W
    • Microprocessor control
    • Can connect to any Wi-Fi network or can operate as an Access Point
    • Controlled via WiFi and a mobile phone, computer, automation system or any other device supporting HTTP and/or UDP protocol

    Es gibt ein Update auf die oben genannte Firmware,


    Shelly 1 / 2 / HT / RGBW2 fw release 1.4.6.

    Shelly 1 and 2:

    - Wi-Fi stability - if device lost Wi-Fi connectivity, will restore it up to 30 seconds.

    - Speed up Wi-Fi connect < 3 sec.

    - Speed up Wi-Fi connect < 2 sec with static IP

    - Shelly2 can be flashed with wrong firmware - fixed

    - Shelly2 reverse button logic in toggle mode - added

    Shelly H&T

    - Speed up Wi-Fi connect < 3 sec.

    - Speed up Wi-Fi connect < 2 sec with static IP.

    Firmware update 1.4.5:

    Bug fixes:

    Shelly2 :

    - report 0.7-1.3W when both channels is off

    - return broken status when settings static IP address

    - Roller mode: position control, auto calibration improved

    - Separate buttons send wrong status

    - auto on/off timers to work in relay mode on MQTT commands

    - Firmware update over MQTT do not work

    Shelly 1:

    - Separate buttons send wrong status

    - Firmware update over MQTT do not work

    Shelly Bulb:

    - Do not wake up when is powered

    Shelly HT:

    - Report wrong battery status.

    - Battery consumption optimization

    Other minor bug is fixed.

    Original soft.

    So habs hinbekommen,über den PC mit dem Handy ging es nicht.

    Leider ist mir in meinem Eifer einer abgeraucht, L und N vertauscht, ich Depp.

    Kommt irgendwann ,wie beim 1er, damit man N und L beliebig anschliessen kann?

    Ich bräuchte noch 4 Stück,wenn es kommt würde ich noch warten mit der Bestellung.